plumbing Chelsea

History of water pipe

This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality.

Lead water pipes were still widely used in the early 20th century, and remain in many households.

In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards. Despite the Romans' common use of lead pipes, their aqueducts rarely poisoned people.

Unlike other parts of the world where lead pipes cause poisoning, the Roman water had so much calcium in it that a layer of plaque prevented the water contacting the lead itself.

What often causes confusion is the large amount of evidence of widespread lead poisoning, particularly amongst those who would have had easy access to piped water.

This was an unfortunate result of lead being used in cookware and as an additive to processed food and drink, for example as a preservative in wine.Roman lead pipe inscriptions provided information on the owner to prevent water theft. Wooden pipes were used in London and elsewhere during the 16th and 17th centuries.

The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through.The multiple pipes were then sealed together with hot animal fat.

They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century.

These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants. Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).Źródło:

Wikipedia about Valves

A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways.
Valves are technically fittings, but are usually discussed as a separate category.
In an open valve, fluid flows in a direction from higher pressure to lower pressure.
The word is derived from the Latin valva, the moving part of a door, in turn from volvere, to turn, roll. The simplest, and very ancient, valve is simply a freely hinged flap which drops to obstruct fluid (gas or liquid) flow in one direction, but is pushed open by flow in the opposite direction. This is called a check valve, as it prevents or "checks" the flow in one direction.

Modern control valves may regulate pressure or flow downstream and operate on sophisticated automation systems. Źródło:

Water systems - materials

plumbing Chelsea
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s.8 Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")11 out of steel, copper, plastic, and cast iron.11 The straight sections of plumbing systems are called "pipes" or "tubes".

A pipe is typically formed via casting or welding, whereas a tube is made through extrusion.

Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding.
These joining techniques are discussed in more detail in the piping and plumbing fittings article.Źródło:

Widok do druku:

plumbing Chelsea